Non-woven laid scrims laminated for single parachute for reinforcement solutions
Non-woven laid scrims Introduction
This product is a Laid Scrim (yarn types multiple options available), a cost-effective, open-mesh reinforcement fabric engineered specifically for single parachute reinforcement composites — laminated into parachute canopy fabrics, reinforcement patches at shroud line attachment points, and steering/orifice zones to act as a hidden tensile grid. It is manufactured by chemically bonding continuous filament yarns into a flat-laid open mesh (square or tri-directional), with binder options (PVOH, PVC, Acrylic, or customized) to match parachute fabric laminating and coating processes. The chemically bonded construction gives the scrim lightweight, high strength, low shrinkage/low elongation, and corrosion resistance, making it capable of withstanding the instant impact of canopy deployment and sustained wind loads in flight without adding unnecessary weight to the parachute system.
Non-woven laid scrims Characteristics
Parachute-Grade Property Profile: Dimensional stability, tensile strength, alkali resistance, tear resistance, fire resistance, anti-microbial properties, water resistance — the scrim's low elongation prevents over-stretching of the canopy fabric during deployment, while multi-directional tear resistance withstands gust shear and snag risks during packing/unpacking and flight, all at minimal added weight to preserve parachute maneuverability.
High Strength & Light Weight: Available in a range of regular mesh sizes and grammages covering the platform's common specifications, delivering high tensile and tear resistance at minimal added weight. Fully bondable with almost any parachute fabric (nylon, polyester, aramid etc.); each roll length up to 50,000 m to support continuous parachute fabric laminating lines.
Long Rolls for Parachute Fabric Lines: Roll width 200–2,500 mm; roll length up to 50,000 m. Fewer splices per shift on high-speed laminating and coating lines feeding parachute mills — fewer weak spots in finished canopy rolls, more consistent batch appearance, reducing defect risks on safety-critical parachute products.
Non-woven laid scrims Data Sheet
|
Item No. |
CF12.5*12.5PH |
CF10*10PH |
CF6.25*6.25PH |
CF5*5PH |
|
Mesh Size |
12.5 x 12.5mm |
10 x 10mm |
6.25 x 6.25mm |
5 x 5mm |
|
Weight (g/m2) |
6.2-6.6g/m2 |
8-9g/m2 |
12-13.2g/m2 |
15.2-15.2g/m2 |
The regular supply of non-woven reinforcement and laminated scrim is 12.5x12.5mm,10x10mm,6.25x6.25mm, 5x5mm,12.5x6.25mm etc. The regular supply grams are 6.5g, 8g, 13g, 15.5g, etc.With high strength and light weight, it can be fully bonded with almost any material and each roll length can be 10,000 meters.
Non-woven laid scrims Application
Primary Use: Reinforcement for Single Parachute Composites
The core application of this parachute-grade laid scrim is as the hidden tensile grid laminated into single parachute canopy fabrics, shroud line attachment patches, and steering/orifice reinforcement zones. It is laminated into the host fabric stack to:
Withstand Deployment Impact & In-Flight Loads
Canopy deployment generates instant peak loads of several kN; the scrim's multi-directional tensile and tear resistance arrests crack initiation at seam crossings, attachment points, and fabric nicks, while low elongation prevents permanent canopy distortion that would affect flight stability and maneuverability.
Reduce Added Weight for Better Maneuverability
The scrim adds meaningful tensile reinforcement at very low GSM, keeping the total parachute system weight down — critical for single parachutes where pilot control and descent rate depend on minimal excess mass.
Improve Throughput on Parachute Lines
50,000 m roll length feeds high-speed laminating and coating lines with fewer splice stops — higher yield per shift, fewer splice-related defects on finished canopy rolls.
Secondary Applications
a) Aluminum Foil Composite
Nove-woven laid scrim is widely applied in aluminium foil industry. It can help manufacture to develop the production efficiency as the roll length can reach 10000m. It also makes the finished product with better apperance.
b) PVC Flooring
PVC Flooring is mainly made of PVC,also other necessary chemical material during manufacture. It is produced by calendering,extrusion progress or other manufacture progress, it is devided into PVC Sheet Floor and PVC Roller Floor. Now all major domestic and foreign manufactures are applying it as the reinforcement layer to avoiding the joint or bulge between pieces, which is caused by the heat expansion and contraction of materials.
c) None-woven category products reinforced
None-woven laid scrim is widely used as reinforced materail on kinds none-woven fabric, such as fiberglass tissue, polyester mat, wipes, also some top ends, such as medical paper. It can makes none-woven products with higher tensile strength,while just add very little unit weight.
d) PVC Tarpaulin
Laid scrim can be used as basic materials to produce truck cover,light awning, banner, sail cloth etc.
